The lights can be yellow or green. After the computer starts, all four lights display solid green. When the computer starts normally, the lights flash. flashing yellow light solved Will a Celeron E3200 work in a Dell Dimension 2400? Check This Out
If you're new to Tech Support Guy, we highly recommend that you visit our Guide for New Members. The computer is in a normal operating condition after POST.None. If the problem persists, see "Contacting Dell" in your Owner's Manual. If the problem persists, see "Contacting Dell" in your Owner's Manual.
Please disable your adblocker only for www.manualslib.com. DMA ErrorDMA 1 ErrorDMA 2 ErrorError in the DMA controller on the system board.The keyboard or system board may need to be replaced. One possible beep code (code 1-3-1) consists of one beep, a burst of three beeps, and then one beep. On the diagnostic lights on back of the cpu only b and d are lit up (they are green).
Continue until you have identified a faulty connector or reinstalled all modules without error. If the problem persists, see "Contacting Dell" in your Owner's Manual for instructions on obtaining technical assistance. If the problem persists, see "Contacting Dell" in your Owner's Manual. http://en.community.dell.com/support-forums/desktop/f/3514/t/19302291 If the computer malfunctions, the color and sequence of the lights identify the problem.
CH-2 Timer ErrorAn error is occurring on the timer on the system board.See "Contacting Dell" in your Owner's Manual for instructions on obtaining technical assistance. INTR1 ErrorINTR2 ErrorAn interrupt channel on the system board failed to POST.The keyboard or system board may need to be replaced. Related This entry was posted on August 13, 2009 at 6:04 pm and is filed under Uncategorized. Your cache administrator is webmaster.
If you hit f2 to enter bios, then esc to exit, the computer will boot just fine into windows and work. 3 answers Last reply Nov 23, 2009 More about dell Can I add an additional card? Dell Abcd Codes If the problem persists, you may need to replace the keyboard. Light Pattern Problem Description Suggested Resolution The computer is in a normal off condition or a possible pre-BIOS failure has occurred.Verify that the computer is plugged into a working electrical outlet
If available, install properly working memory of the same type into your computer. his comment is here If the problem persists, reinstall the card that you removed, remove a different card, and then restart the computer. Code Cause 1-1-2Microprocessor register failure 1-1-3NVRAM 1-1-4ROM BIOS checksum failure 1-2-1Programmable interval timer 1-2-2DMA initialization failure 1-2-3DMA page register read/write failure 3-1-1Slave DMA register failure 3-1-2Master DMA register failure 3-1-3Master interrupt Once out of two times I started it, it booted right into windows....If it works in windows, wouldn't that mean both RAM sticks are working?
A possible floppy or hard drive failure has occurred.Reseat all power and data cables and restart the computer. After the computer starts, all four lights display solid green. Thank you. http://transcoderesearch.com/dell-dimension/dell-dimension-xps-t650r-wont-get-past-initial-dell-screen.html Let it run overnight and see what it comes up with.http://www.memtest86.com/download.html Ask a new question Read More Dell Light Dimension Computers Related Resources Dell Dimension 9200 won't start - diagnostic lights
Check the interface cable at both ends. Reseating the memory modules may fix the beep code errors in the following table. KB/Interface ErrorAn error occurred with the keyboard connector.Ensure that nothing is resting on the keyboard; if a key appears to be stuck, carefully pry it up.
The lights can be yellow or green. http://support.dell.com/support/edocs/systems/dim2400/en/sm_en/advtshoo.htm#1105412 Usually these errors point to a memory or video problem. benjaminl111Nov 22, 2009, 11:27 PM Ahhh thats weird. A possible expansion card failure has occurred.
Check the interface cable at both ends. Memory modules are detected, but a memory configuration or compatibility error exists.Ensure that no special memory module/memory connector placement requirements exist. Invalid Boot DisketteThe operating system cannot be located on drive A or drive C.Enter the system setup program and confirm that drive A or drive C is properly identified. http://transcoderesearch.com/dell-dimension/dell-dimension-dsr-dell-system-restore-question.html We hate rut, but we fear change. ******************************** System error, strike any user to continue...
You can leave a response, or trackback from your own site. Fill in your details below or click an icon to log in: Email (required) (Address never made public) Name (required) Website You are commenting using your WordPress.com account. (LogOut/Change) You are Sign In Upload Page of 100 Go Download Table of ContentsContents Print This PagePrint ShareShare Url of this page: HTML Link: Bookmark Comment Manuals Brands Dell Manuals Desktop Dimension 2400 Series Repeat this process for each card.
evasive Mobo-fu Master Posts: 37357Joined: Sun May 06, 2001 12:01 amLocation: Netherlands Website Top Display posts from previous: All posts1 day7 days2 weeks1 month3 months6 months1 year Sort by AuthorPost Verify that the memory modules that you are installing are compatible with your computer. Diskette Boot FailureDrive A or B is present but has failed the BIOS POST.Ensure that the drive is installed correctly in the computer and defined correctly in the system setup program. If the computer starts normally, move the memory module to a different connector and restart the computer.
Style Default Style Contact Us Help Home Top RSS Terms and Rules Copyright © TechGuy, Inc. If the computer malfunctions, the color and sequence of the lights identify the problem. No diagnostic lights. 12VDC ok. C: Drive ErrorC: Drive FailureThe hard drive is not working or is not configured correctly.Ensure that the drive is installed correctly in the computer and defined correctly in the system setup
No ROM BasicThe operating system cannot be located on drive A or drive C.Enter the system setup program and confirm that drive A or drive C is properly identified. Blog at WordPress.com. Short URL to this thread: https://techguy.org/721716 Log in with Facebook Log in with Twitter Log in with Google Your name or email address: Do you already have an account? This site is completely free -- paid for by advertisers and donations.
Message Possible Cause Corrective Action 8042 Gate-A20 errorThe keyboard controller failed its test.If you receive this message after you make changes in the system setup program, enter the program and restore To eliminate the possibility of a faulty memory connector, remove all memory modules, reinstall one memory module (if the computer supports a single module), and then restart the computer. When the computer starts normally, the lights flash. Quick response time.
Advertisements do not imply our endorsement of that product or service. Show Ignored Content As Seen On Welcome to Tech Support Guy! Newer Than: Search this thread only Search this forum only Display results as threads Useful Searches Recent Posts More...