Test the device Swap the device with a comparable device that works properly. If you install mixed pairs of PC2700 (DDR 333-MHz) and PC3200 (DDR 400-MHz) memory, the modules function at the slowest speed installed. Run the Dell Diagnostics. Remove these other possible causes of interference: Power extension cables Keyboard and mouse extension cables Too many devices on a power strip Multiple power strips connected to the same electrical outlet this contact form
Click Apply and click OK. Why would aliens ally with humans against other humans? Otherwise, your computer may not start properly. If you believe this post is offensive or violates the CNET Forums' Usage policies, you can report it below (this will not automatically remove the post). http://en.community.dell.com/support-forums/desktop/f/3514/t/19328798
Code Cause 1-1-2Microprocessor register failure 1-1-3NVRAM 1-1-4ROM BIOS checksum failure 1-2-1Programmable interval timer 1-2-2DMA initialization failure 1-2-3DMA page register read/write failure 1-3Video Memory Test failure 1-3-1 through 2-4-4Memory not being properly Then repeat steps 10, 11, and 12. Close the computer cover, reconnect the computer and devices to electrical outlets, and then turn them on.
It sounds to me like the RAM upgrade may be a red herring. x:\ is not accessible. If any cables appear loose, reconnect them. Dell Optiplex Gx270 Manual The computer should have changed the value of System Memory to reflect the newly installed memory capacity, speed, and mode (single or dual).
greengreengreengreenThe computer is in a normal operating condition after POST.None. Dell Optiplex Gx270 Drivers Check the mouse settings Windows® XP Click the Start button, click Control Panel, and then click Printers and Other Hardware. If the problem persists, contact the hardware manufacturer for technical assistance. imp source CPU Speed: 2394 MHz ?
A program stops responding End the program Windows XP, Windows 2000, Windows NT Press
If you have two or more memory modules installed, remove the modules, reinstall one module, and then restart the computer. Close the computer cover, reconnect the computer and devices to electrical outlets, and then turn them on. Dell Optiplex Gx270 Specs Other technical problems Go to the Dell Support website Go to support.dell.com for help with general usage, installation, and troubleshooting questions. Dell Optiplex Gx270 Motherboard I guess it has something to do with the dual channel not working properly.
You can do so by touching an unpainted metal surface on the computer chassis. weblink If the problem persists, contact Dell. Verify that the printer is recognized by Windows® Windows XP Click the Start button. See "Floppy drive problems" or "Hard drive problems" for troubleshooting suggestions. Dell Optiplex Gx270 Ram
A program crashes repeatedly Check the software documentation Many software manufacturers maintain websites with information that may help you solve the problem. Brian Cooley found it for you at CES 2017 in Las Vegas and the North American International Auto Show in Detroit. Click Printers and Other Hardware, and then click Phone and Modem Options. navigate here Max memory: 2GB or 4GB.
NOTE: Memory purchased from Dell is covered under your computer warranty. Dell Optiplex Gx270 Memory Upgrade See "Power Problems."If the problem persists, contact Dell for technical assistance. Unintelligible characters print from the printer.
If your computer and attached devices did not automatically turn off when you shut down your computer, turn them off now. Reinstall the operating system. Click Printers and Other Hardware. Dell Optiplex Gx270 Power Supply Try copying the file to a blank disk or using a larger-capacity disk.
Repeat this process until you identify which card is malfunctioning. Remove and then reinstall any cards. Check the printer documentation See the printer documentation for setup and troubleshooting information. his comment is here Diskette write protected The floppy disk is write-protected.
Click Properties, and then select the Ports tab. Ensure that the port settings match the recommended settings. Connect your computer and devices to electrical outlets, and turn them on. If Work Offline has a checkmark next to it, click the checkmark to remove it and connect to the Internet.
Click the program that is no longer responding. Run the Dell Diagnostics to identify a more serious cause. CAUTION: Before you begin any of the procedures in this section, follow the steps in "Safety Instructions." Remove and reinstall the floppy drive See the "Drives" section pertinent to your For a USB printer, ensure that the Print to the following port(s): setting is USB.
See the software documentation for minimum memory requirements. If the problem persists, contact Dell. Ensure that you are connected to the Internet With the Outlook Express e-mail program open, click File. Be sure to install a single memory module in DIMM_1, the connector closest to the processor, before you install modules in the other connectors.
User Agreement, Privacy, Cookies and AdChoice *Learn about pricingThis page was last updated: Feb-07 13:51. Exit system setup and reboot the computer. Try adjusting the settings. Continue until you have identified a faulty connector or reinstalled all modules without error.
Click Control Panel. If the message does not reappear, turn off the computer and reinsert one of the other cards.